Funky Mods

[MrWilly]

No, not the forum mods.
I did this Hogue / HandleIt mashup this evening in order to get a proper grip on my grips. Hogue stopped a bit too low so I butchered some HandleIt sandpaper grips to fill in the top cause that's what I had.
What funky mods have you done on a gun or accessory and why? Show it off here.

 

[RustVendor]

That doesn't even look that funky!

 

[RedHemi]

Nice job, I'm not a fan of grip tape but you actually made it look good.

 

[ikeo1]

No, not the forum mods.

 

[22plinker]

No, not the forum mods.
I did this Hogue / HandleIt mashup this evening in order to get a proper grip on my grips. Hogue stopped a bit too low so I butchered some HandleIt sandpaper grips to fill in the top cause that's what I had.View attachment 247705View attachment 247706
What funky mods have you done on a gun or accessory and why? Show it off here.

I like sand paper, rubberized and some finger groove grips so you've made the best of all worlds with this one.

It looks good too!

Great job

Matt

 

[22plinker]

Here's a funky mod I made.

It's a super extended aluminum baseplate for the Sig Legion pistols.

https://imgur.com/1QSWQ1m

 

[MrWilly]

Here's a funky mod I made.

It's a super extended aluminum baseplate for the Sig Legion pistols.

https://imgur.com/1QSWQ1m

17 rounder?

 

[22plinker]

17 rounder?

10 rounds here in CA...

 

[22plinker]

Here's an updated shorter version with a feature to grasp the mag out of the pistol. (for competitors)

With the Legion's magwell and flush fitting Legion basepad, you can't pull the mag out of the pistol if it happened to get stuck.

https://imgur.com/IpXS80b

https://imgur.com/53tS1vz

https://imgur.com/XjXarl9

 

[RedHemi]

I don't know if you consider this a funky mod but here's my CZ 75b SA frame with a Czechmate upper and Houge grips.

 

[MrWilly]

I don't know if you consider this a funky mod but here's my CZ 75b SA frame with a Czechmate upper and Houge grips.
View attachment 248104

B-E-A-UTIFUL!
I bet it shoots like a dream!

 

[MrWilly]

Here's an updated shorter version with a feature to grasp the mag out of the pistol. (for competitors)

With the Legion's magwell and flush fitting Legion basepad, you can't pull the mag out of the pistol if it happened to get stuck.

https://imgur.com/IpXS80b

https://imgur.com/53tS1vz

https://imgur.com/XjXarl9

Nicely done! I would much rather have these beauties than the IMI base pads I have.

 

[RedHemi]

B-E-A-UTIFUL!
I bet it shoots like a dream!

Nice and flat. Besides the comp it's ported a little. My only problem is it doesn't always lock back after the last round.

 

[Gawernator]

10 rounds here in CA...

sure.. wink wink

 

[22plinker]

sure.. wink wink

Yep, 10 rounds for CA as stated.

(but just imagine the possible capacity considering it's about an inch and a half longer than the factory 21 round mag basepad..)

Matt

 

[Bun_groker]

I don't know if you consider this a funky mod but here's my CZ 75b SA frame with a Czechmate upper and Houge grips.
View attachment 248104

Yeah, that is funky, might be best to go back to stock and sell the upper to me.

 

[RedHemi]

Yeah, that is funky, might be best to go back to stock and sell the upper to me.